Test Instruments for Aviation

Aerofab Part Nos.

          Page 42

​

KASUBS001KIT, Sub Surface Inspection, Low Frequency Including:

PUS16Probe, Surface, Straight, Oia 16mm, 300Hz - 100KHz, Plastic, Lemo 4-Way

KAWEL001KIT, Weld, Probes + Accessorys Including:

PWM100S00Probe, Weld, Oia 16.00mm (Medium) 100kHz, Straight, Oisconnect

PUR11Probe, Surface, Right Angled, Oia 11mm, 300Hz - 100KHz, Plastic, Lemo 4-Way

PUB100kProbe, Unshielded, Broad Band, 100k (35kHz-250kHz), BNC

ATBWAccessory. Test Block, Weld Probe, Ferrous (Steel EN1A) + x 4 0.5mm Shims, 0.5, 1.0, 2.0mm slots

ALL12-L04-015RAccessory, Lead, Lemo 12-Way - Lemo 4-Way, 1.5m (Reflection)

ATB001Accessory, Test Block, Aluminium 7075-T6, 1.6mm Thick, x 4 Flat Bottom Holes 75% (1.2mm), 50% (0.8mm), 25% (0.4mm),
12.5% (0.2mm), Oeep.

ALL12-L04-015BAccessory, Lead, Lemo 12-Way - Lemo 4-Way, 1.5m (Bridge)

ALLCX-B02-015AAccessory, Lead. Lemo 00 to BNC, 1.5m (Vantage)

AW003Accessory, Butterfly PTFE Tape (Pack of 30)

AC002Accessory, Oeluxe Probe Case PHOC1

SURFACE PROBE PACKAGE (TO FIT WELDCHECK, AEROCHECK & AEROCHECK+)

ETher NDE
Part No.Oescription

KAROT001KIT, Rotary Orive Kit (To fit AeroCheck+) Including:

ARO002Accessory, Rotating Orive, Small, Lemo 12-Way. (Mercury)

ETher NDE
Part No.OescriptionALL12-L12-020MAccessory, Lead, Lemo 12-Way - Lemo 12-Way,  2.0m (Rotating Orive)

KASUR001KIT, Surface Inspection Including:

PU500PSFE/NFEProbe, Unshielded, 500kHz, Fe/NFe, Plastic Handle, Straight 100mm Long

PS002PS028-114NProbe, Shielded, 2MHz, Plastic Handle,Straight, 28mm Tip Length (Total Length 114mm, 4.5") (Straight Shank)

PS500PO064-114NProbe, Shielded, 500kHz, Plastic Handle, Oouble Crank, 6.4 (0.25") Tip Length (Total Length 114mm, 4.5") (15o  Crank, 90o  tip Shank)

PS002PO064-114NProbe, Shielded, 2MHz, Plastic Handle, Oouble Crank, 6.4 (0.25") Tip Length (Total Length 114mm, 4.5") (15o  Crank, 90o  tip Shank)

PK065002NFEProbe, Knife, 65o, 2MHz, NFe, Unshielded

ALLCX-M02-015AAccessory, Lead, Lemo 00 to Microdot, 1.5m (VANTAGE, ETi)

ATBFAccessory. Test Block, Ferrous (Steel EN1A), 0.2, 0.5, 1.0mm slots

ATBAAccessory. Test Block,Aluminium Alloy 7075-T6, 0.2, 0.5, 1.0mm
slots

AW003Accessory, Butterfly PTFE Tape (Pack of 30)

AC002Accessory, Oeluxe Probe Case PHOC1

 

 

PROBE KITS CONTINUED...                                                                         PENCIL PROBES
DOUBLE SHIELDED - ABSOLUTE & BRIDGE

CONDUCTIVITY PROBE KIT NIST (FOR AEROCHECK+)
CONDUCTIVITY PROBE KIT NPL (FOR AEROCHECK+)

ETher NDE
Part No.Oescription

KACON001KIT, Conductivity Inspection - NIST - Std Oia 13mm Probe (To fit AeroCheck Plus) Including:

PCON001# Probe, Conductivity, 60kHz, Oia 13.00mm, Straight, Lemo 7-Way (AeroCheck Plus)

ASIG010# Accessory, Oual Conductivity Reference Standards, Nominal Values 8.5% and 101% IACS (SigmaCheck) NIST VALUES

ALL12-L07-012-CON# Accessory, Lead, 12-Way Lemo to 7-Way Lemo, 1.2m, Conductivity (To fit AeroCheck Plus Conductivity Probe)

40516# SKIRT - Conductivity Probe (AeroCheck Plus)

B3061S# SCREW - M3 thumb screw

40517# REFERENCE HOLOER - Oual Condustivity Standard (Thermal Bridge for
Stability)

APCON001# QUICK REFERNCE CARO - Guide to using conductivity probe PCON001

APPLICATION:
ABSOLUTE PENCIL PROBES:  For general purpose inspection of surface breaking defects and metallurgy variations. Uses a Micro connector.
BRIDGE PENCIL PROBES: ETher NOE newly
developed "IB Tech Inside" absolute intrinsically balanced technology which further improves the signal to noise ratio of conventional Absolute Probes giving a significant improvement in inspection reliability. Uses a Lemo 4-Way connector.
SPECIFICATION:
•     Oouble Shielded, used on Fe & NFe applications, Oisconnectable.
•     Non Magnetic Stainless Steel Shanks - Straight, 90o  Tip, 45o  Crank, 15o  crank
+ 90o Tip.
•     Plastic Handle with finger scallops and neoprene grip.
•     Connector - Micro for Absolute and Lemo 4-Way for Bridge (IB Tech Inside).
•     Centre frequency/Operating range - 200kHz (50kHz - 600kHz), 500kHz (150kHz - 1.5MHz), 2MHz - (650kHz - 6MHz), 6MHz - (2MHz - 18MHz).
•     Probe colour coding available.

ETher NDE
Part No.Oescription

KACON002KIT, Conductivity Inspection - NPL - Std Oia 13mm Probe (To fit AeroCheck Plus) Including:

PCON001# Probe, Conductivity, 60kHz, Oia 13.00mm, Straight, Lemo 7-Way (AeroCheck Plus)

ASIG011# Accessory, Oual Conductivity Reference Standards, Nominal Values 8.5% and 101% IACS (SigmaCheck) NPL VALUES

ALL12-L07-012-CON# Accessory, Lead, 12-Way Lemo to 7-Way Lemo, 1.2m, Conductivity (To fit AeroCheck Plus Conductivity Probe)

40516# SKIRT - Conductivity Probe (AeroCheck Plus)

B3061S# SCREW - M3 thumb screw

40517# REFERENCE HOLOER - Oual Condustivity Standard (Thermal Bridge for
Stability)

APCON001# QUICK REFERNCE CARO - Guide to using conductivity probe PCON001

​

STRAIGHT ABSOLUTE WITH PLASTIC HANDLE

STRAIGHT - BRIDGE (IB TECH INSIDE) WITH PLASTIC HANDLE

STANDARD

STANDARD

ETher NDE
Part No.Centre FreqTip Length (Total Length)

 

Tip

TypeETher NDE
Part No.Centre
Freq.Tip Length (Total Length)

 

Tip

Type

Probe, Shielded, Plastic Handle, Straight:

PS200PS028-114N200kHz28mm Tip Length (Total Length
114mm, 4.5") (Straight Shank)4.45Absolute

Probe, Shielded, Plastic Handle, Straight:

PS200PS028-114NB200kHz28mm Tip Length (Total Length 114mm, 4.5") (Straight Shank)4.45Bridge

PS200PS028-114F200kHz28mm Tip Length (Total Length 114mm, 4.5") (Straight Shank)3.30
(Fine)Absolute

PS200PS028-114FB200kHz28mm Tip Length (Total Length 114mm, 4.5") (Straight Shank)3.30
(Fine)Bridge

PS500PS028-114N500kHz28mm Tip Length (Total Length 114mm, 4.5") (Straight Shank)4.45Absolute

PS500PS028-114NB500kHz28mm Tip Length (Total Length 114mm, 4.5") (Straight Shank)4.45Bridge

PS500PS028-114F500kHz28mm Tip Length (Total Length 114mm, 4.5") (Straight Shank)3.30
(Fine)Absolute

PS500PS028-114FB500kHz28mm Tip Length (Total Length 114mm, 4.5") (Straight Shank)3.30
(Fine)Bridge

PS002PS028-114N2MHz28mm Tip Length (Total Length 114mm, 4.5") (Straight Shank)3.30Absolute

PS002PS028-114NB2MHz28mm Tip Length (Total Length 114mm, 4.5") (Straight Shank)3.30Bridge

PS002PS028-114F2MHz28mm Tip Length (Total Length 114mm, 4.5") (Straight Shank)2.34
(Fine)Absolute

PS002PS028-114FB2MHz28mm Tip Length (Total Length 114mm, 4.5") (Straight Shank)2.34
(Fine)Bridge

PS006PS028-114N6MHz28mm Tip Length (Total Length 114mm, 4.5") (Straight Shank)2.34Absolute

PS006PS028-114NB6MHz28mm Tip Length (Total Length 114mm, 4.5") (Straight Shank)2.34Bridge

Other variants available on request
LEADS TO FIT ABOVE PROBES

Specials available on request
LEADS TO FIT ABOVE PROBES

ETher NDE
Part No.OescriptionInstrumentConnector InstrumentConnector Probe EndCable LengthConfig.

ETher NDE
Part No.OescriptionInstrumentConnector InstrumentConnector Probe EndCable LengthConfig.

ALLCX-M02-015ALeadWeldCheck/ AeroCheck/ Vantage/ETiLemo CoaxialMicro Plug1.5mAbsolute

ALL12-L04-015BLeadWeldCheck/ AeroCheck/ Vantage/ETiLemo 12-WayLemo
4-Way Plug1.5mBridge

ALL12-M02-015ALeadWeldCheck/ AeroCheck/ HockingLemo 12-WayMicro Plug1.5mAbsolute

ALL07-L04-015BLeadHockingLemo
7-WayLemo
4-Way Plug1.5mBridge

ALL07-M02-015ALeadHockingLemo 7-WayMicro Plug1.5mAbsolute

ALB02-M02-015ALeadVariousBNC PlugMicro Plug1.5mAbsolute

 

90O TIP - ABSOLUTE WITH PLASTIC HANDLE

 

 

90O TIP - BRIDGE (IB TECH INSIDE) WITH PLASTIC HANDLE

 

STANDARD

STANDARD

ETher NDE
Part No.Centre Freq.Tip Length (Total Length)

 

Tip

 

 

ETher NDE
Part No.Centre
Freq.Tip Length (Total Length)Tip

Probe, Shielded, Plastic Handle, Right angled 90o tip:

Probe, Shielded, Plastic Handle, Right angled 90o tip:

PS200PR050-114N200kHz5.0 (MIN) Tip Length (Total Length
114mm, 4.5") (90deg Tip Shank)4.45

PS200PR050-114NB200kHz5.0 (MIN) Tip Length (Total Length 114mm, 4.5") (90o  Tip Shank)4.45

PS200PR027-114F200kHz2.7 (MIN) Tip Length (Total Length 114mm, 4.5") (90deg Tip Shank)3.30
(Fine)

PS200PR027-114FB200kHz2.7 (MIN) Tip Length (Total Length 114mm, 4.5") (90o  Tip Shank)3.30
(Fine)

PS500PR050-114N500kHz5.0 (MIN) Tip Length (Total Length 114mm, 4.5") (90deg Tip Shank)4.45

PS500PR050-114NB500kHz5.0 (MIN) Tip Length (Total Length 114mm, 4.5") (90o  Tip Shank)4.45

PS500PR027-114F500kHz2.7 (MIN) Tip Length (Total Length 114mm, 4.5") (90deg Tip Shank)3.30
(Fine)

PS500PR027-114FB500kHz2.7 (MIN) Tip Length (Total Length 114mm, 4.5") (90o  Tip Shank)3.30
(Fine)

PS002PR027-114N2MHz2.7 (MIN) Tip Length (Total Length 114mm, 4.5") (90deg Tip Shank)3.30

PS002PR027-114NB2MHz2.7 (MIN) Tip Length (Total Length 114mm, 4.5") (90o  Tip Shank)3.30

PS002PR017-114F2MHz1.7 (MIN) Tip Length (Total Length 114mm, 4.5") (90deg Tip Shank)2.34
(Fine)

PS002PR017-114FB2MHz1.7 (MIN) Tip Length (Total Length 114mm, 4.5") (90o  Tip Shank)2.34
(Fine)

PS006PR017-114N6MHz1.7 (MIN) Tip Length (Total Length 114mm, 4.5") (90deg Tip Shank)2.34

PS006PR017-114NB6MHz1.7 (MIN) Tip Length (Total Length 114mm, 4.5") (90o  Tip Shank)2.34

Specials available on request
LEADS TO FIT ABOVE PROBES

Specials available on request
LEADS TO FIT ABOVE PROBES

ETher NDE
Part No.OescriptionInstrumentConnector InstrumentConnector Probe EndCable LengthConfig.

ETher NDE
Part No.OescriptionInstrumentConnector InstrumentConnector Probe EndCable LengthConfig.

ALLCX-M02-015ALeadWeldCheck/ AeroCheck/ Vantage / ETiLemo CoaxialMicro Plug1.5mAbsolute

ALL12-L04-015BLeadWeldCheck/ AeroCheck/ Vantage/ETi/ HockingLemo 12-WayLemo
4-Way Plug1.5mBridge

ALL12-M02-015ALeadWeldCheck AeroCheck/ Vantage/ETi/ HockingLemo 12-WayMicro Plug1.5mAbsolute

ALL07-L04-015BLeadHockingLemo 7-WayLemo
4-Way Plug1.5mBridge

ALL07-M02-015ALeadHockingLemo 7-WayMicro Plug1.5mAbsolute

ALB02-M02-015ALeadVariousBNC PlugMicro Plug1.5mAbsolute

 

45O  CRANK - ABSOLUTE WITH PLASTIC HANDLE

 

 

45O CRANK - BRIDGE (IB TECH INSIDE) WITH PLASTIC HANDLE

 

STANDARDSTANDARD

ETher NDE
Part No.Centre
FreqTip Length (Total Length)

 

Tip

Type

ETher NDE
Part No.Centre
FreqTip Length (Total Length)TipType

Probe, Shielded, Plastic Handle, Crank:Probe, Shielded, Plastic Handle, Crank:

PS200PC195-114N200kHz19.5 (0.75") Tip Length (Total Length
114mm, 4.5") (45o Crank Shank)4.45AbsolutePS200PC195-114NB200kHz19.5 (0.75") Tip Length (Total Length
114mm, 4.5") (45o Crank Shank)4.45Bridge

PS200PC195-114F200kHz19.5 (0.75") Tip Length (Total Length 114mm, 4.5") (45o Crank Shank)3.30
(Fine)AbsolutePS200PC195-114FB200kHz19.5 (0.75") Tip Length (Total Length 114mm, 4.5") (45o Crank Shank)3.30
(Fine)Bridge

PS500PC195-114N500kHz19.5 (0.75") Tip Length (Total Length 114mm, 4.5") (45o Crank Shank)4.45AbsolutePS500PC195-114NB500kHz19.5 (0.75") Tip Length (Total Length 114mm, 4.5") (45o Crank Shank)4.45Bridge

PS500PC195-114F500kHz19.5 (0.75") Tip Length (Total Length 114mm, 4.5") (45o Crank Shank)3.30
(Fine)AbsolutePS500PC195-114FB500kHz19.5 (0.75") Tip Length (Total Length 114mm, 4.5") (45o Crank Shank)3.30
(Fine)Bridge

PS002PC195-114N2MHz19.5 (0.75") Tip Length (Total Length 114mm, 4.5") (45o Crank Shank)3.30AbsolutePS002PC195-114NB2MHz19.5 (0.75") Tip Length (Total Length 114mm, 4.5") (45o Crank Shank)3.30Bridge

PS002PC195-114F2MHz19.5 (0.75") Tip Length (Total Length 114mm, 4.5") (45o Crank Shank)2.34
(Fine)AbsolutePS002PC195-114FB2MHz19.5 (0.75") Tip Length (Total Length 114mm, 4.5") (45o Crank Shank)2.34
(Fine)Bridge

PS006PC195-114N6MHz19.5 (0.75") Tip Length (Total Length 114mm, 4.5") (45o Crank Shank)2.34AbsolutePS006PC195-114NB6MHz19.5 (0.75") Tip Length (Total Length 114mm, 4.5") (45deg Crank Shank)2.34Bridge

Specials available on request
LEADS TO FIT ABOVE PROBES

Specials available on request
LEADS TO FIT ABOVE PROBES

ETher NDE
Part No.OescriptionInstrumentConnector InstrumentConnector Probe EndCable LengthConfig.

ETher NDE
Part No.OescriptionInstrumentConnector InstrumentConnector Probe EndCable LengthConfig.

ALLCX-M02-015ALeadWeldCheck/ AeroCheck/ Vantage, ETiLemo CoaxialMicro Plug1.5mAbsolute

ALL12-L04-015BLeadWeldCheck/ AeroCheck/ Vantage/ETi/ HockingLemo 12-WayLemo
4-Way Plug1.5mBridge

ALL12-M02-015ALeadWeldCheck/ AeroCheck/ Vantage/ETi HockingLemo 12-WayMicro Plug1.5mAbsolute

ALL07-L04-015BLeadHockingLemo 7-WayLemo
4-Way Plug1.5mBridge

ALL07-M02-015ALeadHockingLemo 7-WayMicro Plug1.5mAbsolute

ALB02-M02-015ALeadVariousBNC PlugMicro Plug1.5mAbsolute

 

15O  CRANK 90O  TIP - ABSOLUTE WITH PLASTIC HANDLE

 

 

15O  CRANK 90O  TIP - BRIDGE (IB TECH INSIDE) WITH PLASTIC HANDLE

 

STANDARD

STANDARD

ETher NDE
Part No.Centre FreqTip Length (Total Length)

 

Tip

TypeETher NDE
Part No.Centre FreqTip Length (Total Length)

 

Tip

Type

Probe, Shielded, Plastic Handle, Oouble crank:

PS200PO050-114N200kHz5.0 (MIN) Tip Length (Total Length
114mm, 4.5") (15o  Crank, 90o  tip Shank)4.45Absolute

Probe, Shielded, Plastic Handle, Oouble crank:

PS200PO050-114NB200kHz5. 0 (MIN) Tip Length (Total Length 114mm, 4.5") (15o  Crank, 90o tip
Shank)4.45Bridge

PS200PO027-114F200kHz2.7 (MIN) Tip Length (Total Length 114mm, 4.5") (15o  Crank, 90o tip Shank)3.30
(Fine)Absolute

PS200PO027-114FB200kHz2.7 (MIN) Tip Length (Total Length 114mm, 4.5") (15o  Crank, 90o tip Shank)3.30
(Fine)Bridge

PS500PO050-114N500kHz5. 0 (MIN) Tip Length (Total Length 114mm, 4.5") (15o  Crank, 90o  tip Shank)4.45Absolute

PS500PO050-114NB500kHz5. 0 (MIN) Tip Length (Total Length 114mm, 4.5") (15o  Crank, 90o tip Shank)4.45Bridge

PS500PO027-114F500kHz2.7 (MIN) Tip Length (Total Length 114mm, 4.5") (15o  Crank, 90o  tip Shank)3.30
(Fine)Absolute

PS500PO027-114FB500kHz2.7 (MIN) Tip Length (Total Length 114mm, 4.5") (15o  Crank, 90o tip
Shank)3.30
(Fine)Bridge

PS002PO027-114N2MHz2.7 (MIN) Tip Length (Total Length 114mm, 4.5") (15o  Crank, 90o  tip Shank)3.30Absolute

PS002PO027-114NB2MHz2.7 (MIN) Tip Length (Total Length 114mm, 4.5") (15o  Crank, 90o tip
Shank)3.30Bridge

PS002PO017-114F2MHz1.7 (MIN) Tip Length (Total Length 114mm, 4.5") (15o  Crank, 90o  tip Shank)2.34
(Fine)Absolute

PS002PO017-114FB2MHz1.7 (MIN) Tip Length (Total Length
114mm, 4.5") (15o  Crank, 90o tip Shank)2.34
(Fine)Bridge

PS006PO017-114N6MHz1.7 (MIN) Tip Length (Total Length 114mm, 4.5") (15o  Crank, 90o  tip Shank)2.34Absolute

PS006PO017-114NB6MHz1.7 (MIN) Tip Length (Total Length 114mm, 4.5") (15o  Crank, 90o  tip Shank)2.34Bridge

Other variants and specials available on request
LEADS TO FIT ABOVE PROBES

Specials available on request
LEADS TO FIT ABOVE PROBES

ETher NDE
Part No.OescriptionInstrumentConnector InstrumentConnector Probe EndCable LengthConfig.

ETher NDE
Part No.OescriptionInstrumentConnector InstrumentConnector Probe EndCable LengthConfig.

ALLCX-M02-015ALeadWeldCheck/ AeroCheck/Lemo CoaxialMicro Plug1.5mAbsolute

ALL12-L04-015BLeadWeldCheck/ AeroCheck/ Vantage/ETi/ HockingLemo 12-WayLemo
4-Way Plug1.5mBridge

ALL12-M02-015ALeadVantage/ETi WeldCheck/ AeroCheck/ HockingLemo 12-WayMicro Plug1.5mAbsolute

ALL07-L04-015BLeadHockingLemo 7-WayLemo
4-Way Plug1.5mBridge

ALL07-M02-015ALeadHockingLemo 7-WayMicro Plug1.5mAbsolute

ALB02-M02-015ALeadVariousBNC PlugMicro Plug1.5mAbsolute

 

 

STRAIGHT - EXTERNAL THREADS (BOLTS)

 

THREAD INSPECTION PROBES (UNSHIELDED)
ABSOLUTE

​

100

APPLICATION:
UNSHIELDED ABSOLUTE THREAD INSPECTION
PROBES: For crack detection in external and internal threads.
SPECIFICATION:
•     Micro connector
•     Centre frequency range - 200kHz 500kHz, 2MHz
•     Operating range - 200kHz (50kHz - 600kHz), 500kHz (150kHz - 1.5MHz), 2MHz - (650kHz
- 6MHz)
•     Used on Fe & NFe applications
•     Oisconnectable
•     Chisel and Pointed versions available
NOTES:
This range of probes comes with either a pointed or chiselled tip.

ETher NDE
Part No.OescriptionCentre Freq.Tip Shape

Probe, Thread, External (Straight), Pointed/Chiselled

PTE200PNFEProbe, Thread, External, 200kHz, Pointed, NFE, Unshielded200kHzPointed

PTE200PFEProbe, Thread, External, 200kHz, Pointed, FE,
Unshielded200kHzPointed

PTE200CNFEProbe, Thread, External, 200kHz, Chisel, NFE,
Unshielded200kHzChisel

PTE200CFEProbe, Thread, External, 200kHz, Chisel, FE, Unshielded.200kHzChisel

PTE500PNFEProbe, Thread, External, 500kHz, Pointed, NFE, Unshielded.500kHzPointed

PTE500PFEProbe, Thread, External, 500kHz, Pointed, FE,
Unshielded.500kHzPointed

PTE500CNFEProbe, Thread, External, 500kHz, Chisel, NFE,
Unshielded.500kHzChisel

PTE500CFEProbe, Thread, External, 500kHz, Chisel, FE,
Unshielded.500kHzChisel

PTE002PNFEProbe, Thread, External, 2MHz, Pointed, NFE,
Unshielded.2MHzPointed

PTE002PFEProbe, Thread, External, 2MHz, Pointed, FE,
Unshielded.2MHzPointed

PTE002CNFEProbe, Thread, External, 2MHz, Chisel, NFE,
Unshielded.2MHzChisel

PTE002CFEProbe, Thread, External, 2MHz, Chisel, FE,
Unshielded.2MHzChisel

 

Other options available on request
LEADS TO FIT ABOVE PROBES

ETher NDE
Part NoOescriptionInstrumentConnector Instr. EndConnector Probe EndCable Lgth.Config.

ALLCX-M02-015ALeadVantage/ETiLemo CoaxialMicro Plug1.5mAbsolute

ALL12-M02-015ALeadHockingLemo 12-WayMicro Plug1.5mAbsolute

ALL07-M02-015ALeadHockingLemo 7-WayMicro Plug1.5mAbsolute

ALB02-M02-015ALeadVariousBNC PlugMicro Plug1.5mAbsolute

 

90O CRANK - EXTERNAL & INTERNAL THREADS (BOLTS & NUTS)65O CRANK - INTERNAL THREADS (NUTS)

 

ETher NDE
Part No.OescriptionCentre Freq.Tip ShapeETher NDE
Part No.OescriptionCentre Freq.Tip Shape

Probe, Thread, Right Angled, Pointed/ChiselledProbe, Thread, Internal (65o), Pointed/Chiselled

PTR200PNFEProbe, Thread, 90o, 200kHz, Pointed, NFE, Unshielded200kHzPointedPTI200PNFEProbe, Thread, Internal 65o, 200kHz, Pointed, NFE, Unshielded200kHzPointed

PTR200PFEProbe, Thread, 90o, 200kHz, Pointed, FE,
Unshielded200kHzPointedPTI200PFEProbe, Thread, Internal 65o, 200kHz, Pointed,
FE, Unshielded200kHzPointed

PTR200CNFEProbe, Thread, 90o, 200kHz, Chisel, NFE,
Unshielded200kHzChiselPTI200CNFEProbe, Thread, Internal 65o, 200kHz, Chisel,
NFE, Unshielded200kHzChisel

PTR200CFEProbe, Thread, 90o, 200kHz, Chisel, FE, Unshielded.200kHzChiselPTI200CFEProbe, Thread, Internal 65o, 200kHz, Chisel, FE, Unshielded.200kHzChisel

PTR500PNFEProbe, Thread, 90o, 500kHz, Pointed, NFE, Unshielded.500kHzPointedPTI500PNFEProbe, Thread, Internal 65o, 500kHz, Pointed, NFE, Unshielded.500kHzPointed

PTR500PFEProbe, Thread, 90o, 500kHz, Pointed, FE,
Unshielded.500kHzPointedPTI500PFEProbe, Thread, Internal 65o, 500kHz, Pointed,
FE, Unshielded.500kHzPointed

PTR500CNFEProbe, Thread, 90o, 500kHz, Chisel, NFE,
Unshielded.500kHzChiselPTI500CNFEProbe, Thread, Internal 65o, 500kHz, Chisel,
NFE, Unshielded.500kHzChisel

PTR500CFEProbe, Thread, 90o, 500kHz, Chisel, FE,
Unshielded.500kHzChiselPTI500CFEProbe, Thread, Internal 65o, 500kHz, Chisel,
FE, Unshielded.500kHzChisel

PTR002PNFEProbe, Thread, 90o, 2MHz, Pointed, NFE,
Unshielded.2MHzPointedPTI002PNFEProbe, Thread, Internal 65o, 2MHz, Pointed,
NFE, Unshielded.2MHzPointed

PTR002PFEProbe, Thread, 90o, 2MHz, Pointed, FE,
Unshielded.2MHzPointedPTI002PFEProbe, Thread, Internal 65o, 2MHz, Pointed,
FE, Unshielded.2MHzPointed

PTR002CNFEProbe, Thread, 90o, 2MHz, Chisel, NFE,
Unshielded.2MHzChiselPTI002CNFEProbe, Thread, Internal 65o, 2MHz, Chisel,
NFE, Unshielded.2MHzChisel

PTR002CFEProbe, Thread, 90o, 2MHz, Chisel, FE,
Unshielded.2MHzChiselPTI002CFEProbe, Thread, Internal 65o, 2MHz, Chisel, FE,
Unshielded.2MHzChisel

Other options available on request
LEADS TO FIT ABOVE PROBESOther options available on request
LEADS TO FIT ABOVE PROBES

ETher NDE
Part NoOescriptionInstrumentConnector Instr. EndConnector Probe EndCable Lgth.Config.ETher NDE
Part NoOescriptionInstrumentConnector Instr. EndConnector Probe EndCable Lgth.Config.

ALLCX-M02-015ALeadVantage/ETiLemo CoaxialMicro Plug1.5mAbsoluteALLCX-M02-015ALeadVantage/ETiLemo CoaxialMicro Plug1.5mAbsolute

ALL12-M02-015ALeadHockingLemo 12-WayMicro Plug1.5mAbsoluteALL12-M02-015ALeadHockingLemo 12-WayMicro Plug1.5mAbsolute

ALL07-M02-015ALeadHockingLemo 7-WayMicro Plug1.5mAbsoluteALL07-M02-015ALeadHockingLemo 7-WayMicro Plug1.5mAbsolute

ALB02-M02-015ALeadVariousBNC PlugMicro Plug1.5mAbsoluteALB02-M02-015ALeadVariousBNC PlugMicro Plug1.5mAbsolute

 

 

ABSOLUTE BROAD BAND PROBES

 

BROAD BAND PROBES
ABSOLUTE & BRIDGE

 

 

ETher NDE
Part No.OescriptionCentre
Freq.Freq.
RangeType /
Connector

Probe, Unshielded, Broad Band

general purpose inspection of surface breaking defects and metallurgy variations and to estimate coating (Paint) thickness.
BRIDGE UNSHIELDED BROAD BAND PROBES: ETHER
NOE newly developed "IB Tech Inside " absolute intrinsically balanced technology which further improves the signal to noise ratio of conventional Absolute Probes giving a significant improvement in inspection reliability. Uses a Lemo 4-Way connector.
SPECIFICATION:
•     Broad range with centre frequency  - 5kHz, 20kHz, 100kHz, 500kHz, 2MHz
•     Plastic Handle with neoprene grip
•     Connector - BNC for Absolute and Lemo 4-Way for Bridge (IB Tech Inside)
NOTES:
A range of balance loads are also available for use with some impedance plane instruments.

PUB2MProbe, Unshielded,
Broad Band, 2MHz2MHz (5.6uH)500kHz -  4MHzAbsolute /
BNC Socket

PUB500KProbe, Unshielded, Broad Band, 500k500kHz (22uH)150kHz - 1MHzAbsolute / BNC Socket

PUB100KProbe, Unshielded, Broad Band, 100k100kHz (82uH)35kHz - 250kHzAbsolute / BNC Socket

PUB20KProbe, Unshielded, Broad Band, 20k20kHz (390uH)7kHz - 60kHzAbsolute/ BNC Socket

PUB5KProbe, Unshielded, Broad Band, 5k5kHz (1500uH)2kHz - 15kHzAbsolute/ BNC Socket

LEADS TO FIT ABOVE PROBES

ETher NDE
Part No.OescriptionInstrumentConnector InstrumentConnector Probe EndCable LengthConfig.

ALLCX-M02-015ALeadWeldCheck/ AeroCheck/ Vantage/ETiLemo CoaxialBNC Plug1.5mAbsolute

ALL12-B02-015ALeadWeldCheck/ AeroCheck/ Vantage/ETi/ HockingLemo 12-WayBNC Plug1.5mAbsolute

ALL07-B02-015ALeadHockingLemo 7-WayBNC Plug1.5mAbsolute

ALB02-B02-015ALeadVariousBNC PlugBNC Plug1.5mAbsolute

 

BRIDGE BROAD BAND PROBES

 

 

ROTATING PROBES
REFLECTION

 

 

ETher NDE
Part No.OescriptionCentre
Freq.Freq.
RangeType /
Connector

DIFFERENTIAL ROTATING PROBES: For internal
diameter inspection of fastener holes, countersinks and counter bores.
SPECIFICATION:
•     Probe diameters from 1.6 to 50mm, available in 0.01mm steps.
•     Fischer connector to ETHER NOE Small and Large drive also compatible with Hocking, GE, Rohmann and Forster drive units.
•     Frequency range from 200kHz to 2MHz.
•     Comes in Rigid Stainless Steel and Oelrin Flexible options.
NOTES:
When ordering Rotating Probes 0.1mm is automatically taken off probe diameter during manufacture, this should be good for typical hole condition and manufacturing tolerances. Where tolerances are poor allow for greater clearance.
Example:  To inspect a    12.7 (1/2") hole a
12.7 probe should be ordered which will be
manufactured to a    12.6.

Probe, Unshielded, Broad Band

PUB2MBProbe, Unshielded,
Broad Band, 2MHz2MHz (5.6uH)500kHz -  4MHzBridge /
LEMO 4-Way

PUB500KBProbe, Unshielded, Broad Band, 500k500kHz (22uH)150kHz - 1MHzBridge /
LEMO 4-Way

PUB100KBProbe, Unshielded, Broad Band, 100k100kHz (82uH)35kHz - 250kHzBridge /
LEMO 4-Way

PUB20KBProbe, Unshielded, Broad Band, 20k20kHz (390uH)7kHz - 60kHzBridge/
LEMO 4-Way 65mm18.0065.0

PRR1900-065Probe. Rotating, Rigid, Oia = 19.00mm, wl = 65mm19.0065.0PRF170-190051Probe. Rotating, Flexible, Oia =
17.0 - 19.0mm wl = 51.00mm17.00 - 19.0011/16"
(17.50mm)51

PRR2000-065Probe. Rotating, Rigid, Oia = 20.00mm, wl = 65mm20.0065.0

PRF190-210051Probe. Rotating, Flexible, Oia =
19.0 - 21.0mm wl = 51.00mm19.00 - 21.003/4" (19.10mm)51

PRR2100-065Probe. Rotating, Rigid, Oia = 21.00mm, wl = 65mm21.0065.0

PRF210-230051Probe. Rotating, Flexible, Oia =
21.0 - 23.0mm wl = 51.00mm21.00 - 23.007/8"
(22.00mm)51

PRR2200-065Probe. Rotating, Rigid, Oia = 22.00mm, wl = 65mm22.0065.0

PRR2300-065Probe. Rotating, Rigid, Oia = 23.00mm, wl = 65mm23.0065.0

PRF230-250051Probe. Rotating, Flexible, Oia =
23.0 - 25.0mm wl = 51.00mm23.00 - 25.0015/16" (23.80mm)51

PRR2400-065Probe. Rotating, Rigid, Oia = 24.00mm, wl = 65mm24.0065.0

PRF250-270051Probe. Rotating, Flexible, Oia =
25.0 - 27.0mm wl = 51.00mm25.00 - 27.001"
(25.40mm)51

PRR2500-065Probe. Rotating, Rigid, Oia = 25.00mm, wl = 65mm25.0065.0

PRF270-290051Probe. Rotating, Flexible, Oia =
27.0 - 29.0mm wl = 51.00mm27.00 - 29.001 1/8"
(28.57mm)51

PRF290-310051Probe. Rotating, Flexible, Oia =
29.0 - 31.0mm wl = 51.00mm29.00 - 31.001 3/16"
(30.17mm)51

PRF310-330051Probe. Rotating, Flexible, Oia =
31.0 - 33.0mm wl = 51.00mm31.00 - 33.001 1/4"
(31.75mm)51

PRF330-350051Probe. Rotating, Flexible, Oia =
33.0 - 35.0mm wl = 51.00mm33.00 - 35.001 3/8"
(34.93mm)51

PRF350-370051Probe. Rotating, Flexible, Oia =
35.0 - 37.0mm wl = 51.00mm35.00 - 37.001 7/16"
(36.51mm)51

PRF370-390051Probe. Rotating, Flexible, Oia =
37.0 - 39.0mm wl = 51.00mm37.00 - 39.001 1/2"
(38.10mm)51

 

STANDARD WELD PROBES
BRIDGE

STANDARD WELD PROBES TYPES AVAILABLE

 

STRAIGHT

 

APPLICATION:
DIFFERENTIAL WELD PROBES: For in-service inspection of welded structures.
SPECIFICATION:
•     Straight, 90o  Inline, 90o  Right Angle
•     Oiameters, 11.0 (Small), 16 (Medium), 32mm (Large)
•     Oisconnectable and integral probe cables
•     Cable lengths from 1.5 to 50 meters
•     Frequency range 100kH, 20kHz, 100-600kHz
•     Minimal lift off signal, can find cracks through paint, oil, conductive and non-conductive coatings
•     Made from hard wearing PET
•     Stainless steel and ceramic tips available on request.
NOTES:
100kHz probes used on standard ferrous welds. 100-600kHz probe can be used on Aluminium and Stainless Steel welds.
20kHz probe can be used on multi-surface applications and Ouplex.

Type"O" = Oia (mm)"L" = Length (mm)

Small1147.5

Medium1655

Large3276.5

90O INLINE90O TRANSVERSE

 

Type"O" = Oia (mm)"L" = Length (mm)"T" = Tip Orop

Small1136.510.3

Medium16504.1

Large3212821.1

 

STANDARD WELD PROBES CODING SYSTEMDISCONNECT WELD PROBES - BRIDGE

PWS100S015L12

 

PW        Probe Weld (Plastic) S            Oia 11.0mm (Small)
M           Oia 16.0mm (Medium) L             Oia 32.0mm (Large)
100        100kHz (Standard)
020        20kHz Enhanced
106        100-600kHz Multi-surface (Aluminium and Stainless Steel welds)
S            Straight
I             90o  Inline
R            90o  Transverse
000        Oisconnect
015        1.5m Cable
050        5.0m Cable
100        10.0m Cable
500        50.0m Cable
1000      1000.0m Cable
L7          7 Way Lemo - Hocking Locator
L12        12 Way Lemo - WeldCheck/AeroCheck Vantage G2, ETi
J6           6 Way Jaeger - Hocking QuickCheck, 1.1 A4          4-way Amphenol - Zetec
C3          3-way Cannon
L14        14 Way Lemo - Vantage G1
W           Water Proof
C            Ceramic (High Temp)
S            Stainless Steel Tip

 

NOTES:
•     A full range of disconnectable weld probes available for quick interchange.
•     Simply select "000" to probe part number as shown
on weld probe coding system on previous page.

ETher NDE
Part No.OescriptionCentre Freq.Configuration

Probe, Weld

PWS100S000Probe, Weld, Small (11.00mm), Straight, Oisconnect100kHzBridge - Lemo 4-Way

PWM100S000Probe, Weld, Medium (16.00mm), Straight, Oisconnect100kHzBridge - Lemo 4-Way

PWL100S000Probe, Weld, Large (32.00mm), Straight, Oisconnect100kHzBridge - Lemo 4-Way

LEADS TO FIT ABOVE PROBES

ETher NDE
Part No.OescriptionInstrumentConnector InstrumentConnector Probe EndCable LengthConfig.

ALL12-L04-015BLeadWeldCheck/ AeroCheck/ Vantage/ETi/ HockingLemo 12-WayLemo
4-Way Plug1.5mBridge

Example Part No:
PWS100S01SL12
Probe, Weld, Oia. 11.0mm (Small), 100kHz, Straight,
1.5m Cable, Lemo 12-Way.

ALL07-L04-015BLeadHockingLemo 7-WayLemo
4-Way Plug1.5mBridge

 

MINIATURE WELD PROBES - BRIDGE

 

 

INTERNAL DIAMETER (ID) PROBES
BRIDGE

STRAIGHT - PW002                                       4-Way Lemo
Connector

APPLICATION:
DIFFERENTIAL ID PROBES: For internal diameter tube inspection, ideal for inspecting tubular heat exchangers.
SPECIFICATION:
•    
F            Flexible
R            Rigid Push/Pull

Example Part No:
CIDL20R
Cable, Internal Oiameter, Oifferential, Lemo 12-Way, 20meters, Rigid Push/Pull.

OTHER OPTIONS AVAILABLE ON REQUEST.
RIGID PUSH / PULL
Lemo 4-Way 2+2 Type
FLEXIBLE

Example Part No:
PID212L20R24k
Probe, Internal Oiameter, Oifferential, Oia 21.2mm, Lemo 12-Way, 20 meters, Rigid Push/Pull, 24kHz

 

 

LOW FREQUENCY (SPOT FACE) PROBES - STRAIGHT

 

LOW FREQUENCY (SPOT FACE) PROBES
STRAIGHT AND 90O

 

LEMO 4-WAY

 

 

REFLECTION   SUB   SURFACE   PROBES:   for   general
purpose inspection of sub-surface corrosion and flaws.
This   probe   has   excellent   depth   penetration making it ideal for multi-layer inspections.
SPECIFICATION:
•     Broad frequency ranges.
•     Excellent low frequency performance.
•     Integrated 4-way Lemo connector.
•     Built in balance coils.
•     Right angled probes are intrinsically balanced.
NOTES:
The lower the frequency the deeper the depth of penetration.

ETher NDE
Part No.Oescription

 

 

Body
MaterialFrequency RangeConnector

Probe, Surface, Straight

PUS07Probe, Surface,
Straight,7mmSt Steel1kHz - 100kHzLemo 4-Way

PUS08Probe, Surface,
Straight,8mmSt Steel1kHz - 100kHzLemo 4-Way

PUS11Probe, Surface,
Straight,11mmAcetal300Hz - 100KHzLemo 4-Way

PUS13Probe, Surface,
Straight,13mmAcetal200Hz - 200KHzLemo 4-Way

PUS16Probe, Surface,
Straight,16mmAcetal300Hz - 100kHzLemo 4-Way

PUS24Probe, Surface,
Straight,24mmAcetal80Hz - 60KHzLemo 4-Way

PUS32Probe, Surface,
Straight,32mmAcetal80Hz - 60KHzLemo 4-Way

LEADS TO FIT ABOVE PROBES

ETher NDE
Part No.OescriptionInstrumentConnector InstrumentConnector Probe EndCable LengthConfig.

ALL12-L04-015RLeadWeldCheck/ AeroCheck/ Vantage/ETi/ HockingLemo 12-WayLemo 4-Way1.5mReflection

ALL07-L04-015RLeadHockingLemo 7-WayLemo 4-Way1.5mReflection

ALJ06-L04-015RLeadHockingJaeger 6-WayLemo 4-Way1.5mReflection

 

SLIDING PROBES
DUAL ELEMENT

SURFACE INSPECTION PROBES - 90O

LEMO 4-WAY

PFS001 - DUAL ELEMENT SLIDING PROBE
LEMO 4-WAY REFLECTION

ETher NDE
Part No.Oescription Body
MaterialFrequency RangeConnector

Probe, Surface, Right Angled

PUR11Probe, Surface,
Right Angled11mmAcetal300Hz - 200KHzLemo 4-Way

PUR13Probe, Surface, Right Angled13mmAcetal200Hz - 200KHzLemo 4-Way

OPTIONAL GUIDE AVAILABLE: P/N: 40090

PUR16Probe, Surface, Right Angled16mmAcetal300Hz - 100kHzLemo 4-Way

PUR24Probe, Surface, Right Angled24mmAcetal80Hz - 60KHzLemo 4-Way

PFS002 - DUAL ELEMENT SLIDING PROBE
2 X MICRO CONNECTORS

PUR32Probe, Surface, Right Angled32mmAcetal80Hz - 60KHzLemo 4-Way

LEADS TO FIT ABOVE PROBES

ETher NDE
Part No.OescriptionInstrumentConnector InstrumentConnector Probe EndCable LengthConfig.

ALL12-L04-015RLeadWeldCheck/ AeroCheck/ Vantage/ETi/ HockingLemo 12-WayLemo 4-Way1.5mReflection

ALL07-L04-015RLeadHockingLemo 7-WayLemo 4-Way1.5mReflection

ALJ06-L04-015RLeadHockingJaeger 6-WayLemo 4-Way1.5mReflection

 

CONDUCTIVITY PROBE

APPLICATION:
Typically  used  on  aircraft  wings  (and  on  other similar structures) to detect cracks and corrosion on  or  near  the  surface  around  fasteners  and  in deeper layers under the skins.
The above probes either slide along or over rows of fasteners.
PROBE CODING:
PFS001: Oual Element Sliding Probe - Reflection
- Lemo 4-Way - contains a transmit and receive element - 400Hz-50kHz - used on fastener head sizes 1mm and below.
PFS002: Oual Element Sliding Probe - Tx, Rx - contains a transmit and receive element - 100Hz-500kHz - Comes with 1.5, 2.5 and 3.5mm wide lens.
LEADS TO FIT ABOVE PROBES

 

APPLICATION:
For   use   with   the   SigmaCheck   Eddy   Current Conductivity Meter. Conductivity is widely used to indicate material type and determine the state of heat treatment.
In order to give accurate readings the SigmaCheck uses  a  three-point  reference  method.  The  first measurement with the probe in the air and then two  further  measurements  are  required  which span the range of interest.
The  SigmaCheck  is  supplied  with  a  detachable reference piece with two standards that cover the range of commonly used metals.

ETher NDE
Part No.OescriptionInstrumentConnector InstrumentConnector Probe EndCable LengthConfig.

ALL12-L04-015RLeadWeldCheck/ AeroCheck/ Vantage/ETi/ HockingLemo 12-WayLemo
4-Way Plug1.5mReflection

ALL12-M02-M02
-015ARLeadWeldCheck/ AeroCheck/ Vantage/ETi/ HockingLemo 12-WayX2 micro Plug1.5m RX TXReflection

 

13MM CONDUCTIVITY PROBE                                                                AEROCHECK CONDUCTIVITY PROBE

 

LEMO 5-WAYLEMO 7-WAYWill only work on  an AEROCHECK+ with lead number:
ALL12-L07-007-CON

ETher NDE
Part No.OescriptionInstrument

PSIG001AProbe, Conductivity, 60, 120, 240 and 480kHz,
Oia 13.00mm, Straight, Lemo 5-WaySigmaCheck

APPLICATION:
For use with the AEROCHECK+ Eddy Current Conductivity Meter feature on the AEROCHECK+ Flaw Oetector. The probe has an internal memory that stores the probe characteristics for calculating conductivity. Only one test frequency can be applied to a probe.

8MM CONDUCTIVITY PROBE
LEMO 5-WAY

PART NUMBER

ETher NDE
Part No.OescriptionInstrument

PCON001Probe, Conductivity, 60kHz, Oia 13.00mm,
Straight, Lemo 7-WayAeroCheck+

ETher NDE
Part No.OescriptionInstrument

PSIG002AProbe, Conductivity, 60, 120, 240 and 480kHz,
Oia 8.00mm, Straight, Lemo 5-WaySigmaCheck

LEADS TO FIT ABOVE PROBES

NOTES:
Each probe is supplied with an SO card, which holds the probes characteristics; this is then inserted into the SigmaCheck being used.

ETher NDE
Part No.OescriptionInstrument

ALL12-L07-012-CONAccessory, Lead, 12-Way Lemo to
7-Way Lemo, 1.2m, ConductivityAeroCheck+

LEADS TO FIT ABOVE PROBES

ETher NDE
Part No.OescriptionInstrument

ALL05-L05-012-SIGA

Accessory, Lead, 5-Way Lemo to 5-Way
Lemo, 1.2m (SigmaCheck)

 

SigmaCheck

 

 

 

 

 

  

AIRCRAFT WHEEL PROBES - BRIDGE                                                 TEST BLOCKS

 

GENERAL PURPOSE WITH SLOTS

 

APPLICATION:
For use with the VeeScan EC wheel inspection system, for detecting surface breaking cracks in wheels.
SPECIFICATION:
Bridge connected absolute (integral balance load) with circular head. Recommended Frequency 200kHz option 100kHz, 500kHz and 1.5 MHz. Recommended diameter 6mm (9mm also available and narrow shaft for large wheels)

APPLICATION:
Test blocks - general purpose with 0.2 (0.008"),
0.5 (0.020") and 1.0mm (0.040") slots to enable
correct calibration.

Part No:Freq.'O'
Oia.'A'
Oia.'B'
Oia.'X'
Lgth'Y'
LgthOescription

PA06-100B100k1/4" (6mm)4.06.35172257Probe, Veescan, Head Oia 6mm 100kHz

PA06-200B200k1/4" (6mm)4.06.35172257Probe, Veescan, Head Oia 6mm 200kHz

PA06-500B500k1/4" (6mm)4.06.35172257Probe, Veescan, Head Oia 6mm 500kHzETher NDE
Part No.OescriptionMaterial

PA06-002B2.0M1/4" (6mm)4.06.35172257Probe, Veescan, Head Oia 6mm 2MHz

PA06-100FB100k1/4" (6mm)4.06.35122207Probe, Veescan, Head Oia 6mm 100kHz Fine Shaft

Accessory, Test Block

ATBFAccessory. Test Block, Ferrous (Steel EN1A), 0.2, 0.5, 1.0mm slotsFerrous (Steel EN1A)

PA06-200FB200k1/4" (6mm)4.06.35122207Probe, Veescan, Head Oia 6mm 200kHz Fine Shaft

ATBAAccessory. Test Block, Aluminium Alloy 7075-T6, 0.2, 0.5, 1.0mm slotsAluminium Alloy 7075-T6

PA06-500FB500k1/4" (6mm)4.06.35122207Probe, Veescan, Head Oia 6mm 500kHz Fine Shaft

ATBTAccessory. Test Block, Titanium 6A14V, 0.2, 0.5, 1.0mm slotsTitanium 6A14V

PA06-002FB2.0M1/4" (6mm)4.06.35122207Probe, Veescan, Head Oia 6mm 2MHz Fine Shaft

ATBSAccessory. Test Block, Stainless Steel 304, 0.2, 0.5, 1.0mm slots (AUSTENITIC)Stainless Steel

Part No:Freq.'O'
Oia.'A'
Oia.'B'
Oia.'X'
Lgth'Y'
LgthOescription

ATBS316Accessory. Test Block, Stainless Steel 316, 0.2, 0.5, 1.0mm slotsStainless Steel 316

PA09-100B100k3/8" (9mm)6.356.35172257Probe, Veescan, Head Oia 9mm 100kHz

PA09-200B200k3/8" (9mm)6.356.35172257Probe, Veescan, Head Oia 9mm 200kHz

PA09-500B500k3/8" (9mm)6.356.35172257Probe, Veescan, Head Oia 9mm 500kHz

PA09-002B2.0M3/8" (9mm)6.356.35172257Probe, Veescan, Head Oia 9mm 2MHz

PA09-100FB100k3/8" (9mm)6.356.35122207Probe, Veescan, Head Oia 9mm 100kHz
Fine Shaft

PA09-200FB200k3/8" (9mm)6.356.35122207Probe, Veescan, Head Oia 9mm 200kHz Fine Shaft

PA09-500FB500k3/8" (9mm)6.356.35122207Probe, Veescan, Head Oia 9mm 500kHz Fine Shaft

PA09-002FB2.0M3/8" (9mm)6.356.35122207Probe, Veescan, Head Oia 9mm 2MHz Fine Shaft

 

CONDUCTIVITY TEST BLOCK

 

APPLICATION:
Used as a reference in the application of electrical conductivity measurement of non- ferrous metals. Ideal for both laboratory and field use.  Blocks are supplied with calibration certificates.
CALIBRATION:
•     Blocks are tested and are certified and traceable to National Standard (NPL, UK) Conductivity References.
•     Blocks are calibrated at 20oC, at a frequency of 60kHz and to an accuracy of +/- 1.2% of the value or +/-0.4% IACS; whichever is less.

ETher NDE
Part No.Material% IACS
(Value Range)Siemens/m
(Value Range)

ATBC-COPPERCopper(99.9-102.5)(57.9-59.5)

ATBC-ALU1200Aluminium Alloy, 1200-H4(57.2-60.5)(33.2-35.1)

ATBC-ALU6082Aluminium Alloy, 6082-T6(45.1-49.0)(25.4-28.4)

ATBC-ALU6061Aluminium Alloy, 6061-T6(40.5-45.0)(23.4-25.4)

ATBC-ALU2014A-T6Aluminium Alloy, 2014A-T6(37.0-40.3)(21.7-23.4)

ATBC-ALU2014A-T4Aluminium Alloy, 2014A-T4(34.7-36.9)(20.1-23.4)

ATBC-ALU7075Aluminium Alloy, 7075-T6(30.0-34.1)(17.4 -19.8)

ATBC-ALU5083Aluminium Alloy, 5083(26.6-30.0)(15.4-17.4)

ATBC-BRASSBrass, CZ 121(23.3-26.6)(13.5-15.4)

ATBC-PBRONZEPhosphor Bronze(16.8-21.9)(9.8-12.7)

ATBC-NICSILVERNickel Silver, LC1291(9.0-9.9)(5.2-5.7)

ATBC-STST303SStainless Steel, 303 S(2.1-2.5)(1.2-1.4)

ATBC-TITANIUMTitanium, 6AL-4V(1.0-1.1)(0.6-0.7)

Note: Conductivity values vary, for current stock values please contact  sales@ethernde.com.
Precise values will be shown on each block.

 

WELD PROBE TEST BLOCK

 

PROBE LEADS

 

NOTES:
Leads come as standard in a 1.5m cable length. Other lengths available on request.
ETHER NDE WELDCHECK, AEROCHECK, AEROCHECK+, VANTAGE G2, ETi (LEMO COAXIAL / LEMO OO - ABSOLUTE)

 

APPLICATION:
Coating thickness calibration standard with
0.5 (0.02"), 1.0 (0.04") and 2.0mm (0.08")
slots including x4 0.5mm (0.02") shims, used in conjunction with Broad Band (paint) Probe PUB100k to set sensitivity levels before weld
inspection.

ETher NDE
Part No.OescriptionInstrumentConnector InstrumentConnector Probe EndCable LengthConfig.

ALLCX-B02-015ALeadETherLemo OOBNC Plug1.5mAbsolute

ALLCX-M02-015ALeadETherLemo OOMicro Plug1.5mAbsolute

ETHER NDE WELDCHECK, AEROCHECK, AEROCHECK+, VANTAGE G2, ETi - HOCKING PHASEC 2200/Dϲ0/Dϲ2, PHASEC 3D, PHASEC 2D, PHASEC 2S, LOCATOR 3,
(LEMO 12-WAY)

ETher NDE
Part No.OescriptionMaterial

Accessory, Test Block, Weld

ATBWAccessory. Test Block, Weld Probe, Ferrous
(Steel EN1A) + x4 0.5mm Shims, 0.5, 1.0, 2.0mm slotsFerrous (Steel EN1A)
+ x4 0.5mm Shims

ETher NDE
Part No.OescriptionInstrumentConnector InstrumentConnector Probe EndCable LengthConfig.

ATBWOUPAccessory. Test Block, Weld Probe, Ouplex, 2205 x4 0.5mm Shims, 0.5, 1.0, 2.0mm slotsOuplex x4 0.5mm
Shims

ALL12-L04-015RLeadETher/HockingLemo 12-WayLemo 4-Way1.5mReflection

ALL12-L04-015BLeadETher/HockingLemo 12-WayLemo 4-Way1.5mBridge

ALL12-M02-015ALeadETher/HockingLemo 12-WayMicro Plug1.5mAbsolute

ALL12-B02-015ALeadETher/HockingLemo 12-WayBNC Plug1.5mAbsolute

ALL12-B02-B02- 015BLeadETher/HockingLemo 12-WayBNC Plug x21.5mBridge

ALL12-L05-015FLeadETher/HockingLemo 12-WayLemo 5-Way1.5mFastScan

 

PROBE ADAPTERS

 

HOCKING PHASEC / QUICK CHECK (JAEGER 6-WAY)

 

ETher NDE
Part No.OescriptionInstrumentConnector InstrumentConnector Probe EndCable LengthConfig.

ALJ06-L04-015RLeadHockingJaeger 6-WayLemo 4-Way1.5mReflection

ALJ06-L04-015BLeadHockingJaeger 6-WayLemo 4-Way1.5mBridge

NOTES:
Adapters come (as standard) in 150mm length. Other lengths available on request.

BNC (CABLE TYPE RG174)

ETher NDE
Part No.OescriptionInstrumentConnector InstrumentConnector Probe EndCable LengthConfig.

ALB02-B02-015ALeadVariousBNC PlugBNC Plug1.5mAbsolute

ETher NDE
Part No.OescriptionInstrumentConnector InstrumentConnector Probe EndCable LengthConfig.

ALB02-M02-015ALeadVariousBNC PlugMicro Plug1.5mAbsolute

AAL12P-L07SAdapterETher/ HockingLemo 12-WayLemo 7-Way1.5mAll

AAL12-J06PAdapterETher/ HockingLemo 12-WayJaeger 6-Way1.5mAll

AAL12-Z04SBAdapterETher/ HockingLemo 12-WayAmphenol 4-Way1.5mBridge

HOCKING LOCATOR 2, LOCATOR 2S (LEMO 7-WAY)

AAL12-Z04SRAdapterETher/ HockingLemo 12-WayAmphenol 4-Way1.5mReflection

ETher NDE
Part No.OescriptionInstrumentConnector InstrumentConnector Probe EndCable LengthConfig.

AAL07P-L12SAdapterHockingLemo 7-WayLemo 12-Way1.5mAll

ALL07-L04-015RLeadHockingLemo 7-WayLemo 4-Way1.5mReflection

ALL07-L04-015BLeadHockingLemo 7-WayLemo 4-Way1.5mBridge

ALL07-M02-015ALeadHockingLemo 7-WayMicro Plug1.5mAbsolute

ALL07-B02-015ALeadHockingLemo 7-WayBNC1.5mAbsolute

ALL07-B02-B02- 015ALeadHockingLemo 7-WayBNC Plug x21.5mAbsolute

 

MERCURY "MINI" ROTARY DRIVE

AALCX-B02S - ACCESSORY, ADAPTER, LEMO OO TO BNC JACK (SHORT) (LEMO 00 TO BNC)

 

Eddy current rotary inspections of fastener holes and countersinks are performed routinely in the Aircraft Maintenance Industry, but also now increasingly used in for the inspection of bolt-holes on wind turbines.
High-speed surface inspection is also another area of increasing usage.
Perfect for tight spaces, the Mercury Rotary Orive is designed and manufactured in-house. Featuring a clearly visible alarm LEO and a camera thread mounting to facilitate easy attachment to an inspection fixture.
Compatible with the AeroCheck, AeroCheck+, Vantage G2, ETi 200, Hocking Phasec 2 & 3 and Industry Standard 4 Pin Fischer Rotary Probes.
SPECIFICATION:

AAB02-LCXS - ACCESSORY, ADAPTER, BNC SOCKET TO LEMO 00 SOCKET (SHORT) (BNC TO LEMO OO)

ETher Part NumberARO002

ConnectorLEMO 12 Way

AAL12P-B02S - ACCESSORY, ADAPTER, 12-WAY LEMO TO BNC SOCKET (FIXED 61MM LONG)

Rotation Speed3000, 2700, 2400, 2100, 1800, 1500, 1200, 1020, 840 and 600 rpm

OimensionsHeight: 80.9mm, Width: 25mm, Length: 34.5mm

Weight300 grams

LEADS TO FIT

ETher NDE
Part No.OescriptionInstrument

ALL12-L12-020MAccessory, Lead, Lemo 12-Way -
Lemo 12-Way, 2.0m (Rotating Orive)AeroCheck/
Vantage G2 ETi/Hocking

Full range of Rotary Test Blocks available

 

EDDY CURRENT EQUIPMENT                                    USEFUL EDDY CURRENT FORMULAE AVAILABLE FROM ETHER NDE

 

AEROCHECK+
Eddy Current Flaw OetectorAEROCHECK
Eddy Current Flaw Oetector

 

WELDCHECK
Eddy Current Flaw OetectorETi-200 Advanced Eddy Current Flaw Oetector

 

VEESCAN Aircraft Wheel Inspection System

SIGMACHECK Eddy Current Conductivity Meter

You can download this and other useful Eddy Current Information from our website.

 

Find out more about all these products and
more at ethernde.com

 

We have local distributors worldwide who are on hand
to help you with all your ETHER NDE products.
To contact your local distributor please email sales@ethernde.com and we will put you directly in touch with them.

ETHER NDE offer a full range of Eddy Current NOT Equipment and Services including:
Flaw Oetectors Conductivity Meters
Aircraft Wheel Inspection Systems
Calibration & Repair

ETHER NDE, Endeavour House, Unit 18, Brick Knoll Park Ashley Road, St Albans, Herfordshire, AL1 5UG, UK
+44 (0)1727 648050
sales@ethernde.com
ethernde.com

 

Oocument number 5032: Issue 5